Baby Lock Accord

• This does not identify an industrial/commercial needle-system code or authorize an unlisted exact needle product.

Use recommended home sewing machine needles in the documented size range of 65/9 through 100/16.

• Match the exact table row, trial sew first, and never use thread of 20 weight or lower.

Use thread in the documented 30-90 weight range. For lightweight fabric use 65/9-75/11 with 60-90 polyester or 50-80 cotton/silk; for medium fabric use 75/11-90/14 with 60-90 polyester or 50-60 cotton/silk. For heavyweight denim/canvas, the table pairs 100/16 with 30-weight polyester/cotton, or 90/14-100/16 with 60-weight polyester or 30-50 cotton/silk. For stretch fabric use ballpoint 75/11-90/14 with 50-weight cotton/polyester/silk. For top-stitching, the table pairs 90/14-100/16 with 30-weight polyester/cotton or 75/11-90/14 with 50-60 weight polyester/cotton. When using transparent nylon thread, use a home sewing machine topstitching needle regardless of fabric or thread. For embroidery use 75/11, or 90/14 on heavier fabric such as denim.

• Use only a recommended straight home sewing machine needle and follow the complete safety order on pages 41-42.

Raise the needle, cover the needle-plate hole with fabric or paper, lock the controls, loosen the needle-clamp screw counterclockwise and remove the old needle. Insert a straight replacement with its flat side toward the rear until it touches the stopper, securely tighten the clamp screw clockwise, then unlock the controls.

• No substitute part number or cross-brand equivalence is established.

Use the included bobbin or the same type, identified as X52800-120.

• This is exact BLMCC evidence tied to X52800-120 or the same type; it does not establish unrestricted Class 15 or cross-brand interchangeability.

The manual identifies X52800-120 as a Class 15 type bobbin.

• Only the depicted height and material are established; diameter and complete geometry remain unknown, and the claim remains bound to X52800-120 or the same-type restriction.

The specified bobbin is plastic and 11.5 mm (approximately 7/16 inch) high.

• Follow the source order and use the correct foot for the selected stitch. This proves the source-native pin/notch mechanism, not a standardized shank class or universal-foot fit.

Raise the needle, lock the controls, raise the presser-foot lever, press the holder's black release button, align the foot pin with the holder notch, lower the lever until the pin snaps into the notch, raise the lever to verify attachment, then unlock the controls.

• Loosen the screw to remove the holder; do not remove the screw itself. The source does not state an unlock step in this holder procedure. The source-specific procedure does not establish dimensions, generic screw-on feet or adapter compatibility.

For cleaning or a foot that does not use the holder, lock the controls, remove the foot, loosen the holder screw toward the back of the machine counterclockwise and remove the holder. To reattach it, raise the lever, align the holder with the lower-left side of the presser bar, hold it in place, and securely tighten the screw toward you clockwise.

• No universal, third-party, cross-brand or standardized-shank compatibility is asserted.

Use presser feet designed specifically for this machine and the correct foot for the selected stitch.

• Only exact accepted Accord BLMCC and this retained Baby Lock August2025 accessory catalog; other names, suffixes, generations and regions remain separate.
• This is a manufacturer chart classification, not dimensions, a universal adapter/holder promise, an offered retail unit, supplied equipment or proof that every accessory in the group fits. Follow exact manual and accessory conditions.
• Keep the printed G/L code: G is the accessory group; L uses the existing evidence engine low-shank mapping. No measured shank height, interchangeable holder or generic foot fit is established.

Low shank (the OEM group/shank chart prints G/L).