bernette bernette 35

• Switch off and unplug for foot or needle setup, then perform the specified clearance check before sewing.
• For bernette b35 and its English January 2026 fourth-edition manual only. Earlier workbook information and its limitations remain separate. Switch off for needle-area adjustments; switch off and unplug before maintenance, adding or removing parts, and changing the needle. These stronger instructions still apply where the care chapter says ‘off and/or unplug.’ Based on documentation reviewed using AI, without personal human review, hands-on testing, a rating-plate check or confirmation that replacement products fit. Use the complete manufacturer instructions and diagrams.

Select B, button-sew-on foot, tension 2–6, length 0 and lowered feed; adjust width for the button holes. Check needle entry by turning the handwheel by hand, sew about 10 stitches and leave about 10 cm tails to wrap/secure a thread shank.

• The limit refers to button diameter, not the b05’s 3 cm buttonhole claim. The adjustable button-holder gap and the forbidden slider/spring-holder gap are different places; follow both instructions.
• For bernette b35 and its English January 2026 fourth-edition manual only. Earlier workbook information and its limitations remain separate. Switch off for needle-area adjustments; switch off and unplug before maintenance, adding or removing parts, and changing the needle. These stronger instructions still apply where the care chapter says ‘off and/or unplug.’ Based on documentation reviewed using AI, without personal human review, hands-on testing, a rating-plate check or confirmation that replacement products fit. Use the complete manufacturer instructions and diagrams.

The sliding foot’srear holder sets the buttonhole size and takes a button up to 1 in (2.5 cm) diameter. Test thick buttons and, if necessary, leave a holder gap to lengthen the hole. Lower the buttonhole lever fully. Keep no gap between the slider and spring holder to avoid unequal sides.

• Automatic buttonhole formation does not guarantee that the motor stops at the end. The pictured reset is the mechanical buttonhole selector reset, not a factory reset, electronic memory or firmware operation.
• For bernette b35 and its English January 2026 fourth-edition manual only. Earlier workbook information and its limitations remain separate. Switch off for needle-area adjustments; switch off and unplug before maintenance, adding or removing parts, and changing the needle. These stronger instructions still apply where the care chapter says ‘off and/or unplug.’ Based on documentation reviewed using AI, without personal human review, hands-on testing, a rating-plate check or confirmation that replacement products fit. Use the complete manufacturer instructions and diagrams.

The manual says it automatically forms front bartack, left row, rear bartack and right row, then tells the operator to stop at the ending point. To repeat, turn the selector to the visually marked reset position and back to the buttonhole symbol; raise the lever fully after finishing. Length knob right gives coarser density, left tighter.

• Use the exact sliding foot and switch off for needle-area work; switch off and unplug before adding or removing parts. Cord type or size and knife-based cutting are not specified here. This is not a complete standalone guide.
• For bernette b35 and its English January 2026 fourth-edition manual only. Earlier workbook information and its limitations remain separate. Switch off for needle-area adjustments; switch off and unplug before maintenance, adding or removing parts, and changing the needle. These stronger instructions still apply where the care chapter says ‘off and/or unplug.’ Based on documentation reviewed using AI, without personal human review, hands-on testing, a rating-plate check or confirmation that replacement products fit. Use the complete manufacturer instructions and diagrams.

With the foot raised, hook filler cord on its rear pin, bring both ends forward beneath it and into the front slits. Sew the usual buttonhole over the cord, pull the left end tight and draw it to the underside with a darning needle. For cutting, place pins at both ends before the bartacks and use the seam ripper.

With the needle raised, choose the pattern using the selector knob. Separate stitch-length and stitch-width knobs adjust those settings.

• Keep the zigzag example separate from the general tension examples: some needle thread beneath a zigzag is intended. Thread visible underneath is not always a fault. No bobbin-screw procedure or universal tension setting is supplied here.
• For bernette b35 and its English January 2026 fourth-edition manual only. Earlier workbook information and its limitations remain separate. Switch off for needle-area adjustments; switch off and unplug before maintenance, adding or removing parts, and changing the needle. These stronger instructions still apply where the care chapter says ‘off and/or unplug.’ Based on documentation reviewed using AI, without personal human review, hands-on testing, a rating-plate check or confirmation that replacement products fit. Use the complete manufacturer instructions and diagrams.

The manual’sideal zigzag has no bobbin thread on the right side and a little needle thread on the wrong side. Its general too-tight example lowers the dial if bobbin thread shows on top; its too-loose example raises the dial if needle thread shows underneath.

• The earlier S/red stretch-stitch selection guidance remains separate. This answer describes the mechanical balance adjustment and range, not an electronic reset or a stored program.
• For bernette b35 and its English January 2026 fourth-edition manual only. Earlier workbook information and its limitations remain separate. Switch off for needle-area adjustments; switch off and unplug before maintenance, adding or removing parts, and changing the needle. These stronger instructions still apply where the care chapter says ‘off and/or unplug.’ Based on documentation reviewed using AI, without personal human review, hands-on testing, a rating-plate check or confirmation that replacement products fit. Use the complete manufacturer instructions and diagrams.

Higher length-dial numbers make longer stitches; the zigzag length range is 0.5–4. For stretch-pattern balance, turn toward minus to condense and plus to expand; the later stretch chapter says expand condensed stitches with plus and condense expanded stitches with minus.

• This does not establish an automatic securing program or a reverse lever that stays engaged by itself. When using the sliding buttonhole foot, the manual separately directs the thread ends to the left.
• For bernette b35 and its English January 2026 fourth-edition manual only. Earlier workbook information and its limitations remain separate. Switch off for needle-area adjustments; switch off and unplug before maintenance, adding or removing parts, and changing the needle. These stronger instructions still apply where the care chapter says ‘off and/or unplug.’ Based on documentation reviewed using AI, without personal human review, hands-on testing, a rating-plate check or confirmation that replacement products fit. Use the complete manufacturer instructions and diagrams.

Keep the reverse lever depressed to sew backward. The starting/finishing instructions use several reverse stitches, then return to forward sewing; lift the foot and draw threads to the rear before using the manual thread cutter.

• These are separate stitch-letter and mode instructions. The manual’s hand-wound elastic bobbin-thread example does not approve a substitute bobbin or establish a general bobbin-tension procedure.
• For bernette b35 and its English January 2026 fourth-edition manual only. Earlier workbook information and its limitations remain separate. Switch off for needle-area adjustments; switch off and unplug before maintenance, adding or removing parts, and changing the needle. These stronger instructions still apply where the care chapter says ‘off and/or unplug.’ Based on documentation reviewed using AI, without personal human review, hands-on testing, a rating-plate check or confirmation that replacement products fit. Use the complete manufacturer instructions and diagrams.

Vari-overlock F uses the zigzag foot, tension 2–6, length 2–3, width 5. Smocking C uses S, tension 1–4, width 5. For shell edging, use lightweight fabric folded/on bias and let the needle clear the folded edge. For smocking, straight-length 4 gathering rows are 1 cm apart; pull bobbin threads, secure, decorate between rows and remove gathering stitches.

• Use this model’s stitch letters and required feet. Decorative stitches do not establish hoop or computer embroidery, a separate quilting motor mode or a complete free-motion guide.
• For bernette b35 and its English January 2026 fourth-edition manual only. Earlier workbook information and its limitations remain separate. Switch off for needle-area adjustments; switch off and unplug before maintenance, adding or removing parts, and changing the needle. These stronger instructions still apply where the care chapter says ‘off and/or unplug.’ Based on documentation reviewed using AI, without personal human review, hands-on testing, a rating-plate check or confirmation that replacement products fit. Use the complete manufacturer instructions and diagrams.

Use B with satin-stitch foot, tension 1–4, length 0.5–1 and width 5. Baste or fuse the appliqué, stitch along its outer edge, stop needle-down at a corner, lift the foot and pivot. Stretch-pattern balance is adjusted with the length knob.

• Follow the arrows in this model’s original diagram; another model’s left/right instructions may differ. Restore normal feed after hand-guided or button-sewing tasks as directed.
• For bernette b35 and its English January 2026 fourth-edition manual only. Earlier workbook information and its limitations remain separate. Switch off for needle-area adjustments; switch off and unplug before maintenance, adding or removing parts, and changing the needle. These stronger instructions still apply where the care chapter says ‘off and/or unplug.’ Based on documentation reviewed using AI, without personal human review, hands-on testing, a rating-plate check or confirmation that replacement products fit. Use the complete manufacturer instructions and diagrams.

Remove the sewing table to the left and open the bobbin cover. Press the feed lever down and move it along the illustrated lowering arrow. For raising, press down, move along the other arrow and turn the handwheel counterclockwise.

• Switch off and unplug. Remove only the parts shown in the chapter and follow the complete reassembly diagrams. The care chapter’s ‘off and/or unplug’ wording does not weaken the earlier safety instructions. This does not cover timing adjustments or opening electrical housings.
• For bernette b35 and its English January 2026 fourth-edition manual only. Earlier workbook information and its limitations remain separate. Switch off for needle-area adjustments; switch off and unplug before maintenance, adding or removing parts, and changing the needle. These stronger instructions still apply where the care chapter says ‘off and/or unplug.’ Based on documentation reviewed using AI, without personal human review, hands-on testing, a rating-plate check or confirmation that replacement products fit. Use the complete manufacturer instructions and diagrams.

With the prescribed isolation, raise the needle, open the bobbin cover, remove the case by latch, open the race-ring holders and remove ring/shuttle. Clean using a brush and soft dry cloth. Refit the shuttle by its center pin against the driver, align the ring pin/notch, lock holders and refit case.

• Switch off and unplug. Use the exact oil-point and shuttle removal/reassembly diagrams. Another model’s needle-bar oiling points or six-month schedule do not apply here; the care chapter’s ‘and/or’ wording does not weaken the safety instructions.
• For bernette b35 and its English January 2026 fourth-edition manual only. Earlier workbook information and its limitations remain separate. Switch off for needle-area adjustments; switch off and unplug before maintenance, adding or removing parts, and changing the needle. These stronger instructions still apply where the care chapter says ‘off and/or unplug.’ Based on documentation reviewed using AI, without personal human review, hands-on testing, a rating-plate check or confirmation that replacement products fit. Use the complete manufacturer instructions and diagrams.

The shuttle-race chapter specifies suitable high-quality sewing-machine oil, 1–2 drops at the illustrated location and removal of excess from the plate. If it will not be used for a time, defer oil until next use. Clean the hook area with brush/soft dry cloth before oiling.

• Switch off and unplug. These instructions do not specify compressed air, solvents, water or further disassembly.
• For bernette b35 and its English January 2026 fourth-edition manual only. Earlier workbook information and its limitations remain separate. Switch off for needle-area adjustments; switch off and unplug before maintenance, adding or removing parts, and changing the needle. These stronger instructions still apply where the care chapter says ‘off and/or unplug.’ Based on documentation reviewed using AI, without personal human review, hands-on testing, a rating-plate check or confirmation that replacement products fit. Use the complete manufacturer instructions and diagrams.

Remove needle and foot, undo the plate setscrew, remove the plate, brush dust/lint from the feed dog and refit the plate.

• Instructions for making a dust cover do not mean one is supplied. Overall machine dimensions, storage temperature and compatibility with an extension table are not established here.
• For bernette b35 and its English January 2026 fourth-edition manual only. Earlier workbook information and its limitations remain separate. Switch off for needle-area adjustments; switch off and unplug before maintenance, adding or removing parts, and changing the needle. These stronger instructions still apply where the care chapter says ‘off and/or unplug.’ Based on documentation reviewed using AI, without personal human review, hands-on testing, a rating-plate check or confirmation that replacement products fit. Use the complete manufacturer instructions and diagrams.

The removable sewing table has an accessory box and locks back onto the free arm through its guides. Free-arm sewing serves tubular garments such as sleeves, waistbands and trouser legs. Carry using the handle while supporting the machine with the other hand; avoid high humidity, radiators and direct sunlight in storage.

• Read your machine’s rating plate. Its frequency, current, wattage and motor output have not been checked here, and travel-adapter or transformer suitability is not confirmed. Do not use another model’s controller types or ratings.
• For bernette b35 and its English January 2026 fourth-edition manual only. Earlier workbook information and its limitations remain separate. Switch off for needle-area adjustments; switch off and unplug before maintenance, adding or removing parts, and changing the needle. These stronger instructions still apply where the care chapter says ‘off and/or unplug.’ Based on documentation reviewed using AI, without personal human review, hands-on testing, a rating-plate check or confirmation that replacement products fit. Use the complete manufacturer instructions and diagrams.

The safety page permits controller C-1028 for 100–120 V or KD-2902 for 220–240 V. Before connection, check that the voltage shown on the machine matches the supply. These controller-specific ranges do not establish an automatically switching dual-voltage machine.

• This connection and speed-control description does not establish automatic needle stopping or compatibility with a replacement pedal.
• For bernette b35 and its English January 2026 fourth-edition manual only. Earlier workbook information and its limitations remain separate. Switch off for needle-area adjustments; switch off and unplug before maintenance, adding or removing parts, and changing the needle. These stronger instructions still apply where the care chapter says ‘off and/or unplug.’ Based on documentation reviewed using AI, without personal human review, hands-on testing, a rating-plate check or confirmation that replacement products fit. Use the complete manufacturer instructions and diagrams.

Switch OFF, connect the machine plug to its power/foot-control socket, connect the wall plug, then switch ON. Pedal pressure changes speed: more pressure runs faster. Keep objects off the pedal to prevent unintended intermittent running.

• Follow the exact regional and original power-supply restrictions. This summary supplies no electrical-service procedure or warranty advice and does not classify every regional version alike.
• For bernette b35 and its English January 2026 fourth-edition manual only. Earlier workbook information and its limitations remain separate. Switch off for needle-area adjustments; switch off and unplug before maintenance, adding or removing parts, and changing the needle. These stronger instructions still apply where the care chapter says ‘off and/or unplug.’ Based on documentation reviewed using AI, without personal human review, hands-on testing, a rating-plate check or confirmation that replacement products fit. Use the complete manufacturer instructions and diagrams.

The manual describes double insulation except USA/Canada. Double-insulated service is for qualified personnel using identical parts; do not add grounding. It calls the machine household-use equipment and asks for especially attentive cleaning/care under intensive use.

• These are settings for the described task, not universal defaults. Raise the needle out of the fabric before changing the pattern and check needle clearance with the correct foot.
• For bernette b35 and its English January 2026 fourth-edition manual only. Earlier workbook information and its limitations remain separate. Switch off for needle-area adjustments; switch off and unplug before maintenance, adding or removing parts, and changing the needle. These stronger instructions still apply where the care chapter says ‘off and/or unplug.’ Based on documentation reviewed using AI, without personal human review, hands-on testing, a rating-plate check or confirmation that replacement products fit. Use the complete manufacturer instructions and diagrams.

Choose A with the zigzag foot, tension 2–6 and length 1.5–4. The needle-position illustration associates width-dial endpoints 0 and 5 with two positions; these are not a 5 mm wide straight stitch. Lower the needle into the fabric, lower the foot, place tails rearward and guide gently while the machine feeds.

• The seam-guide measurement depends on needle position. Do not keep using a center-based allowance after changing the needle position without checking it.
• For bernette b35 and its English January 2026 fourth-edition manual only. Earlier workbook information and its limitations remain separate. Switch off for needle-area adjustments; switch off and unplug before maintenance, adding or removing parts, and changing the needle. These stronger instructions still apply where the care chapter says ‘off and/or unplug.’ Based on documentation reviewed using AI, without personal human review, hands-on testing, a rating-plate check or confirmation that replacement products fit. Use the complete manufacturer instructions and diagrams.

Plate marks measure from the center needle position: front numbers are centimeters and rear numbers are inch fractions. The square-corner example uses 5/8 in (1.6 cm): stop, lower the needle with the handwheel, raise the foot, pivot/re-align the edge to the guide, lower the foot and continue.

• The chapter and overview give different tension settings; no preferred default is selected here. The A/5 entry applies to the described task and does not permit a wider needle or foot. Trim without cutting stitches.
• For bernette b35 and its English January 2026 fourth-edition manual only. Earlier workbook information and its limitations remain separate. Switch off for needle-area adjustments; switch off and unplug before maintenance, adding or removing parts, and changing the needle. These stronger instructions still apply where the care chapter says ‘off and/or unplug.’ Based on documentation reviewed using AI, without personal human review, hands-on testing, a rating-plate check or confirmation that replacement products fit. Use the complete manufacturer instructions and diagrams.

Zigzag B uses the zigzag foot, tension 2–5 and length 0.5–4in the chapter. Three-step C uses tension 1–4, length 0.5–4 and width 5. Its overview gives a different 2–6 tension for B.

• These are overlock-style stitches on a sewing machine. They do not establish a cutting serger, a separate looper system or differential feed. Use this model’s own stitch letters; another model’s letters may differ.
• For bernette b35 and its English January 2026 fourth-edition manual only. Earlier workbook information and its limitations remain separate. Switch off for needle-area adjustments; switch off and unplug before maintenance, adding or removing parts, and changing the needle. These stronger instructions still apply where the care chapter says ‘off and/or unplug.’ Based on documentation reviewed using AI, without personal human review, hands-on testing, a rating-plate check or confirmation that replacement products fit. Use the complete manufacturer instructions and diagrams.

Stretch-overlock F uses S length mode, width 5 and tension 1–4. Triple straight A uses S with tension 2–6; triple zigzag B uses S, width 2–5 and tension 2–6. The reinforced stitch sequence is two forward stitches and one reverse; guide without fighting the alternating feed.

• Spool-net, cap-size and external-stand requirements from other machines have not been applied to this model.
• For bernette b35 and its English January 2026 fourth-edition manual only. Earlier workbook information and its limitations remain separate. Switch off for needle-area adjustments; switch off and unplug before maintenance, adding or removing parts, and changing the needle. These stronger instructions still apply where the care chapter says ‘off and/or unplug.’ Based on documentation reviewed using AI, without personal human review, hands-on testing, a rating-plate check or confirmation that replacement products fit. Use the complete manufacturer instructions and diagrams.

Pull the spool pins up for use and push them down for storage. If thread tends to tangle around a pin, route it through the pin’shole with the hole facing the spool, as illustrated.

• Switch off for threading under the needle-area safety rule. Follow the complete illustrated route; this summary is not a standalone threading guide.
• For bernette b35 and its English January 2026 fourth-edition manual only. Earlier workbook information and its limitations remain separate. Switch off for needle-area adjustments; switch off and unplug before maintenance, adding or removing parts, and changing the needle. These stronger instructions still apply where the care chapter says ‘off and/or unplug.’ Based on documentation reviewed using AI, without personal human review, hands-on testing, a rating-plate check or confirmation that replacement products fit. Use the complete manufacturer instructions and diagrams.

Raise the take-up lever fully with the handwheel toward you and raise the foot. Feed from the back of the spool into the top guide, down through tension and around the check-spring holder, up through take-up right-to-left, down through the head guide right-to-left and the guide on the left of the needle bar; thread the needle front-to-back.

• Switch off for needle-area work. This does not establish a powered threader, permission to thread twin needles with it, or its minimum needle size.
• For bernette b35 and its English January 2026 fourth-edition manual only. Earlier workbook information and its limitations remain separate. Switch off for needle-area adjustments; switch off and unplug before maintenance, adding or removing parts, and changing the needle. These stronger instructions still apply where the care chapter says ‘off and/or unplug.’ Based on documentation reviewed using AI, without personal human review, hands-on testing, a rating-plate check or confirmation that replacement products fit. Use the complete manufacturer instructions and diagrams.

Raise the needle fully, lower the threader fully and turn it away so its hook passes through the eye from behind. Take thread around the guide and beneath the hook; turn the threader toward you and release slowly while holding the end to draw a loop through the eye.

• These are possible causes to check, not a diagnosis of your machine or permission to adjust timing or bobbin-case tension. Keep the special-needle guidance and switch off or unplug as required before setup work.
• For bernette b35 and its English January 2026 fourth-edition manual only. Earlier workbook information and its limitations remain separate. Switch off for needle-area adjustments; switch off and unplug before maintenance, adding or removing parts, and changing the needle. These stronger instructions still apply where the care chapter says ‘off and/or unplug.’ Based on documentation reviewed using AI, without personal human review, hands-on testing, a rating-plate check or confirmation that replacement products fit. Use the complete manufacturer instructions and diagrams.

The table checks thread routes/tension, needle condition/insertion/size, needle-thread match and correct starting tails. Bobbin-thread breaks can involve wrong case threading, lint or a damaged bobbin; replace a damaged bobbin. Poor feed points to lint or an overly fine stitch; puckering can call for a shorter stitch.

• Do not force a jam with the power on. Pulling the handwheel is not a sewing mode. This answer does not diagnose an electrical fault or establish an interlock.
• For bernette b35 and its English January 2026 fourth-edition manual only. Earlier workbook information and its limitations remain separate. Switch off for needle-area adjustments; switch off and unplug before maintenance, adding or removing parts, and changing the needle. These stronger instructions still apply where the care chapter says ‘off and/or unplug.’ Based on documentation reviewed using AI, without personal human review, hands-on testing, a rating-plate check or confirmation that replacement products fit. Use the complete manufacturer instructions and diagrams.

Check power connection, thread jam in the shuttle race and a disengaged clutch caused by a pulled-out handwheel. Noise can involve thread or lint in the race; use the specified isolated cleaning procedure.

• This concerns only the illustrated bobbin-winder adjustment, not the bobbin-case tension screw. Follow the full isolation instructions and diagram; it is not a standalone service guide or a calibration guarantee.
• For bernette b35 and its English January 2026 fourth-edition manual only. Earlier workbook information and its limitations remain separate. Switch off for needle-area adjustments; switch off and unplug before maintenance, adding or removing parts, and changing the needle. These stronger instructions still apply where the care chapter says ‘off and/or unplug.’ Based on documentation reviewed using AI, without personal human review, hands-on testing, a rating-plate check or confirmation that replacement products fit. Use the complete manufacturer instructions and diagrams.

The adjustment row says clockwise when thread builds toward the top and counterclockwise when it builds toward the bottom. Do not turn the illustrated adjusting screw more than one full turn because parts may detach.