Sewing & embroidery reference
Needles, bobbins, feet and other details for this model. Check the requirements before choosing parts.
Before choosing a part
Start with these documented details. Read the requirements with each answer before choosing a needle, bobbin or foot.
The 2024 accessory catalog places the named DESIGNER BRILLANCE80 occurrence in machine group7. Its instructions use the group number to read individual accessory badges.
Requirements and sources →Raise needle highest, pull foot down and toward you, align its cross pin with the ankle gap and push until it snaps in place.
Requirements and sources →The manual recommends needle system130/705H.
Requirements and sources →Not yet confirmed here: Presser-foot shank type, Foot holder / mount, Foot interface / generation, Bobbin type / class, Bobbin material, Bobbin diameter, Bobbin height, Hook type, Needle sizes by fabric and use, Maximum stitch / zigzag width, Feed system, Bobbin loading direction. What is still to confirm →
Accessory groups refer to the named catalog and category. A shared group or snap-on attachment does not mean every accessory fits.
Other names, regional versions and related models have not been confirmed here. A shared manual, product line or accessory group does not identify the machine's family.
Read all original conditions, safety prerequisites and cited illustrated steps before acting. This answer does not establish interchangeable parts, a standardized mounting generation, universal accessory fit or retail sales-unit compatibility.
Documents and page references →Read all original conditions, safety prerequisites and cited illustrated steps before acting. This answer does not establish interchangeable parts, a standardized mounting generation, universal accessory fit or retail sales-unit compatibility.
Documents and page references →Read all original conditions, safety prerequisites and cited illustrated steps before acting. This answer does not establish interchangeable parts, a standardized mounting generation, universal accessory fit or retail sales-unit compatibility.
Documents and page references →Read all original conditions, safety prerequisites and cited illustrated steps before acting. This answer does not establish interchangeable parts, a standardized mounting generation, universal accessory fit or retail sales-unit compatibility. Preserve the source’s needle style, size, thread and clearance qualifications.
Documents and page references →Read all original conditions, safety prerequisites and cited illustrated steps before acting. This answer does not establish interchangeable parts, a standardized mounting generation, universal accessory fit or retail sales-unit compatibility. Loading instructions do not by themselves identify a replacement bobbin class or hook system.
Documents and page references →Read all original conditions, safety prerequisites and cited illustrated steps before acting. This answer does not establish interchangeable parts, a standardized mounting generation, universal accessory fit or retail sales-unit compatibility.
Documents and page references →Read all original conditions, safety prerequisites and cited illustrated steps before acting. This answer does not establish interchangeable parts, a standardized mounting generation, universal accessory fit or retail sales-unit compatibility.
Documents and page references →Read all original conditions, safety prerequisites and cited illustrated steps before acting. This answer does not establish interchangeable parts, a standardized mounting generation, universal accessory fit or retail sales-unit compatibility.
Documents and page references →Read all original conditions, safety prerequisites and cited illustrated steps before acting. This answer does not establish interchangeable parts, a standardized mounting generation, universal accessory fit or retail sales-unit compatibility.
Documents and page references →Read all original conditions, safety prerequisites and cited illustrated steps before acting. This answer does not establish interchangeable parts, a standardized mounting generation, universal accessory fit or retail sales-unit compatibility.
Documents and page references →Read all original conditions, safety prerequisites and cited illustrated steps before acting. This answer does not establish interchangeable parts, a standardized mounting generation, universal accessory fit or retail sales-unit compatibility. Loading instructions do not by themselves identify a replacement bobbin class or hook system.
Documents and page references →Read all original conditions, safety prerequisites and cited illustrated steps before acting. This answer does not establish interchangeable parts, a standardized mounting generation, universal accessory fit or retail sales-unit compatibility. Keep the exact named hoop/module and any model-specific setup limits.
Documents and page references →Read all original conditions, safety prerequisites and cited illustrated steps before acting. This answer does not establish interchangeable parts, a standardized mounting generation, universal accessory fit or retail sales-unit compatibility.
Documents and page references →Read all original conditions, safety prerequisites and cited illustrated steps before acting. This answer does not establish interchangeable parts, a standardized mounting generation, universal accessory fit or retail sales-unit compatibility.
Documents and page references →Read all original conditions, safety prerequisites and cited illustrated steps before acting. This answer does not establish interchangeable parts, a standardized mounting generation, universal accessory fit or retail sales-unit compatibility.
Documents and page references →Use this dated catalog and the exact named-model context. Its group number does not establish every accessory, mounting dimensions or a seller’s offered unit.
Documents and page references →Keep complete article412616145, both group-to-model and group-to-item joins, and all listed exclusions. The conditional application does not establish standardized shank geometry, installed equipment or retail fit.
Documents and page references →Manuals, parts books & more
Publisher links below distinguish a matched file from a listing.
Choose the document for your task: an instruction manual, service manual, parts list and accessory guide answer different questions.
About this document & page references →
Instruction manualEdition: Printed identifier4710526-26D; copyright2018 is not publication date
Models referenced here: Husqvarna Viking DESIGNER BRILLIANCE 80
Cited retained manual: Page references refer to the retained source identified here. Current OEM downloads checked on 2026-10-14 differ from that file; no matching download or page-jump link is offered for this manual. The original is retained privately and is not hosted by SewIndex.
About this document & page references →
Accessory compatibilityEdition: 2024 cover; filename01032024 not interpreted as calendar date
Models referenced here: Husqvarna Viking DESIGNER BRILLIANCE 80
Read the source document ↗
We checked that this file matched the source used here on 2026-10-10. The publisher may later replace its file.
Read the model-specific requirements with each answer before choosing parts.
The manual recommends needle system130/705H.
Do not use asymmetrical twin needles; they can damage the machine.
For through-needle winding use an original HUSQVARNA VIKING bobbin logo-up, needle and foot raised, horizontal main spool and a metal presser foot.
Use the model-designed bobbin logo-up; thread unreels from the left and the bobbin rotates counterclockwise when pulled. Route right then left into springA until click, aroundB/cutterC, replace coverD and cut left atE.
Raise needle highest, pull foot down and toward you, align its cross pin with the ankle gap and push until it snaps in place.
The 2024 accessory catalog places the named DESIGNER BRILLANCE80 occurrence in machine group7. Its instructions use the group number to read individual accessory badges.
In this catalog, Accessory Ankle412616145 applies to the exact Brilliance80 through group7; the individual item displays groups5/6/7/8.
Specifications apply to the named model and document edition. Read any setup, fabric or safety requirements with the answer.
This manual lists DESIGNER Royal Hoop(360x200), Crown Hoop(260x200) and Splendid Square Hoop(120x120) as included.
Place stabilizer beneath fabric; hoop smooth fabric and stabilizer securely with right sides up, align inner-hoop arrow at bottom, close quick release and adjust retaining screw for taut fabric.
Metal Hoop920362096 is180x130mm on page81, but the86/87 chart row says7x5in/180x100mm. The exact Brilliance80 column has X on that row.
Clean often; no lubrication(oiling) is needed. Brush the bobbin area after several projects or lint accumulation; do not blow air into it.
The start/stop button starts and stops sewing or embroidery without the foot control.
Do not use the cutter when an accessory is attached in the two small circular needle-plate holes above the bobbin cover.
Published sewing speed is1050 stitches/minute maximum.
The retained English User’s Guide prints4710526-26D and copyright2018KSIN Luxembourg II, S.a.r.l.
Switch the machine off (“0”) before threading the needle or bobbin, changing the needle or changing the presser foot.
Unplug immediately after use and before cleaning, removing covers or user-servicing adjustments.
Check that the foot control is type FR5 before connecting it.
Insert the new needle fully upwards with the flat side away from you, using the multipurpose tool, then tighten with the screwdriver.
With needle and presser foot raised, route the thread through pre-tensionA, guideB, tension discsC, take-upD from the right, then final guideE.
The threader is designed for needles70–120; do not use it for60or smaller, wing/twin/triple needles, or with the Sensor One-Step buttonhole foot attached.
The catalog explicitly names DESIGNER BRILLIANCE80 for Multi Function Foot Control920561096 but shows8/9 badges, while its machine list places the model in group7.
For fabric that does not feed, check that free-motion mode is not selected and feed teeth are not set down.
These are manufacturer part references. A drawing or matching number alone does not confirm that a replacement from a seller fits. Check the model-specific listing and restrictions.
Manufacturer catalog references are listed below. Replacement compatibility has not been checked.
These conditional catalog answers join the named model to its catalog group, then to the exact item row. Keep the edition, item and pack limits. They do not establish a generic bobbin class, standardized mount, replacement procedure or a seller’s offered-unit fit.
In this catalog, Accessory Ankle412616145 applies to the exact Brilliance80 through group7; the individual item displays groups5/6/7/8.
Full catalog answer and all conditions →
HUSQVARNA VIKING Accessory User’s Guide 2024 · 2024 cover; filename01032024 not interpreted as calendar date · PDF page 2 · printed page unnumbered introductory page · HUSQVARNA VIKING Accessory User’s Guide 2024 · 2024 cover; filename01032024 not interpreted as calendar date · PDF page 5 · printed page 5 · HUSQVARNA VIKING Accessory User’s Guide 2024 · 2024 cover; filename01032024 not interpreted as calendar date · PDF page 93 · printed page 93 · HUSQVARNA VIKING Accessory User’s Guide 2024 · 2024 cover; filename01032024 not interpreted as calendar date · PDF page 87 · printed page 87 · HUSQVARNA VIKING Accessory User’s Guide 2024 · 2024 cover; filename01032024 not interpreted as calendar date · PDF page 96 · printed page 96
Check the exact model and part before ordering. Missing information does not mean a part is incompatible.
Use the full source procedure and its safety precautions. A short referenced answer is not a substitute for service documentation or qualified electrical/mechanical repair.
Service-manual availability and service-only procedures remain unestablished unless separately cataloged and reviewed.
Answers use this model’s manual. Other editions, accessory groups and replacement parts need their own supporting references.
An unanswered question does not mean a part is incompatible. We have not confirmed enough information to recommend it.
Bobbin — System or interchangeability: Not established Full recorded limit & conditions →
Presser foot — Standardized fit and feed version: Not established Full recorded limit & conditions →
Documents — Other oem document coverage: Not established Full recorded limit & conditions →
Source conflict · Setup — Foot control 920561096 · named-model/group discrepancy unresolved: The catalog explicitly names DESIGNER BRILLIANCE80 for Multi Function Foot Control920561096 but shows8/9 badges, while its machine list places the model in group7. Full source conflict & conditions →
Source conflict · Embroidery — Metal hoop 920362096 · dimensions disagree: Metal Hoop920362096 is180x130mm on page81, but the86/87 chart row says7x5in/180x100mm. The exact Brilliance80 column has X on that row. Full source conflict & conditions →
Recorded source conflicts remain visible with their cited editions and original conditions. Other names, regional versions, production history and additional specifications or documents are not fully covered here. Their absence is not a “none exist” finding.
These are research questions, not claims that the missing relationship exists.
Each answer links to its exact evidence passage below. Open a reference to see the document and page. These links identify the source; they do not include the full manual or its diagrams. Document access is consolidated in the OEM library above.
Published by HUSQVARNA VIKING · Printed identifier4710526-26D; copyright2018 is not publication date · English
Exact accepted DESIGNER BRILLIANCE80 manual scope; edition4710526-26D. No sibling/variant/system/item inference.
Checked against the document text.
Document and available links →About this document →PDF page 129 · printed page 129
PDF page 2 · printed page unnumbered safety page
PDF page 12 · printed page 12
PDF page 15 · printed page 15
PDF page 24 · printed page 24
PDF page 30 · printed page 30
PDF page 31 · printed page 31
PDF page 32 · printed page 32
PDF page 35 · printed page 35
PDF page 37 · printed page 37
PDF page 44 · printed page 44
PDF page 171 · printed page 171
PDF page 172 · printed page 172
PDF page 175 · printed page 175
PDF page 180 · printed page 180
Published by HUSQVARNA VIKING · 2024 cover; filename01032024 not interpreted as calendar date · English
Exact 2024 English catalog source-local context only; full page badges/cells and spread geometry in frozen48db7986 and complete independent review. BRILLANCE literal occurrence retained, no alias or global group authority.
Checked against the document text.
Document and available links →About this document →PDF page 2 · printed page unnumbered introductory page
Open the source document · PDF p. 2 ↗ About this document link
PDF page 5 · printed page 5
Open the source document · PDF p. 5 ↗ About this document link
PDF page 93 · printed page 93
Open the source document · PDF p. 93 ↗ About this document link
PDF page 87 · printed page 87
Open the source document · PDF p. 87 ↗ About this document link
PDF page 96 · printed page 96
Open the source document · PDF p. 96 ↗ About this document link
PDF page 81 · printed page 81
Open the source document · PDF p. 81 ↗ About this document link
PDF page 86 · printed page 86
Open the source document · PDF p. 86 ↗ About this document link
Alex Shick · Founder and editor. Corrections managed by Alex Shick.
This Husqvarna Viking DESIGNER BRILLIANCE 80 guide is based on documents, with AI assistance to organize the information. We have not tested or repaired the machine.
Check the document edition with each answer. A source review date is not a machine inspection date or a promise that the manual is the latest edition.
Contact the SewIndex team or report a correction ↗
The correction address has been tested and its monitoring confirmed. We cannot promise a response or accept every suggested change.
Report an error with the model, document and page · About SewIndex and our method
Answers come from the documents named on this page. They describe those editions, and may not cover later changes to the machine or manual.
Source review: The 22 manual entries retain author verification. The independent manual review sampled the needle-threader and cleaning/oiling answers; it did not review every manual claim. The four accessory-catalog entries have a separate review, with both recorded conflicts retained. Page references identify the cited retained editions; current manual downloads have not been matched.