Janome Continental M6

• Use the manual’s lockout-key sequence and the correct foot for foot, holder and needle-plate changes. Also follow its power precautions: switch off and unplug before attaching or removing parts. Read the complete illustrated instructions.
• The holder’s diameter range is not a claim that every finished buttonhole is exactly that length.
• Use L/S on the foot’s adjusting screw only as described after checking a test buttonhole.

Automatic buttonhole foot R’s holder accepts button diameter 1–2.5 cm (⅜–1 inch). Lower the buttonhole lever fully and leave no gap between slider and front stopper. Test on matching fabric; heavy/specific fabrics or threads can require length adjustment, and stretch/fine fabric needs interfacing. A missing lowered lever triggers a warning and stop after a few stitches.

• Keep the same placement for the repeat; do not conflate this with a second independently positioned buttonhole.

After the first automatic buttonhole finishes, restart without raising the foot or lever and without reselecting the pattern to sew another layer. This function is disabled when Thread Cut after Auto-Lock is on. Ordinary completion stops automatically needle-up; raise the buttonhole lever fully after the work.

• These are Janome catalog classifications for Continental M6 / CM6. Check the actual machine and its instructions before choosing accessories.
• A shank or feed-system label does not confirm holder dimensions, adapter needs or whether a replacement foot fits.
• Catalog groups and codes do not establish alternative model names, production dates or interchangeable parts.
• This is the explicit maximum-zigzag-width column, not a guaranteed width for every stitch, twin-needle setup, foot or needle plate. Keep narrower operating limits from the model manual.

9 mm (maximum zigzag width in the Janome accessory catalog).

• Use the manual’s lockout-key sequence and the correct foot for foot, holder and needle-plate changes. Also follow its power precautions: switch off and unplug before attaching or removing parts. Read the complete illustrated instructions.
• These instructions cover only the named feet. They do not confirm a replacement product or classify the shank; the catalog’s shank listing is cited separately.

The holder-removal section names optional professional-grade HP, ruler-work QR, darning PD-H and optional dual-feed AD. With needle raised and machine locked out, raise the foot and remove the thumbscrew/holder. Reattach the holder to the presser bar from behind and tighten securely with the screwdriver.

• Use the manual’s lockout-key sequence and the correct foot for foot, holder and needle-plate changes. Also follow its power precautions: switch off and unplug before attaching or removing parts. Read the complete illustrated instructions.
• Both the AD/HP2 section and these accessories are marked optional.
• HP2 additionally requires the HP plate as specified in its dedicated sewing section.
• Follow the complete illustrated sequence; this is not cross-machine accessory fitment.

Attach the dual-feed holder from behind, finger-tighten the screw, and engage the dual-feed link with the upper feed drive. Lower the foot and manually lower the needle fully before finally tightening with the screwdriver.

• Use the manual’s lockout-key sequence and the correct foot for foot, holder and needle-plate changes. Also follow its power precautions: switch off and unplug before attaching or removing parts. Read the complete illustrated instructions.
• The spring/darning-foot pin placement is not the ordinary snap-foot pin/groove mount.
• No ruler thickness, clearance or third-party fit is established here.

QR attaches to the presser bar from behind and is secured by its thumbscrew. PD-H or open-toe PD-H attaches with its pin on the needle-clamp screw, then its thumbscrew is tightened. Remove the ordinary foot holder first.

• Use the manual’s lockout-key sequence and the correct foot for foot, holder and needle-plate changes. Also follow its power precautions: switch off and unplug before attaching or removing parts. Read the complete illustrated instructions.
• HP and HP2 are distinct feet; do not replace their requirement with a generic straight-stitch plate or universal foot claim.
• Plate and feet remain optional, not presumed standard accessories.

Both professional-grade HP and dual-feed professional-grade HP2 require the optional professional-grade needle plate HP. HP’s plate is for left-position straight stitching. Unsuitable patterns are not displayed for the installed plate/foot application.

• Use the manual’s lockout-key sequence and the correct foot for foot, holder and needle-plate changes. Also follow its power precautions: switch off and unplug before attaching or removing parts. Read the complete illustrated instructions.
• Never turn the needle-plate release dial while the machine is running.
• The optional HP plate is distinct and uses left-position straight stitching.
• Follow the whole plate-change sequence; no maximum stitch width is inferred from plate interlocks.

The straight-stitch plate supports left, center and right straight-stitch positions; its three holes support the fabric. The manual recommends U1–U3 for straight sewing. Unsuitable patterns are disabled. Use the release-key/lockout procedure to replace plates, verify the proper foot, and turn the handwheel slowly to check needle clearance before unlocking.

• Connect/disconnect according to the power-off sequence.
• No fault diagnosis or button repair is inferred from this normal interlock.

The manual expressly disables START/STOP while a foot control is connected. Without it, START/STOP begins slowly then reaches the slider setting; holding the button keeps sewing slow. Holding it during sewing slows the machine and releasing it stops. The button is red while running and blue when stopped.

• No numeric maximum stitches-per-minute rating is inferred from these controls.
• The shutdown is a safety feature, not a specified duty cycle or permission to keep sewing overloaded.

The slider limits maximum speed: right increases, left decreases, and it can be changed while stitching. A fully depressed pedal reaches that slider limit. Startup speed can be set slow, medium or high separately for START/STOP and foot control. An automatic shutdown protects against overload overheating; follow the actual screen instructions.

• Use the exact stitch group; the manual points to printed pages 41, 61–62, 67 and 117 for the special actions.
• Pattern numbers are interpreted within their named menu, not as universal stitch IDs.

No. For Utility 1, 4, 9–12; Applique 10; Quilt 1–3; and Bridge 1–6, holding Reverse sews backward and releasing resumes forward. When stopped with the pedal disconnected it reverses slowly only while held. Utility 2/3 and Buttonhole 2/15/16 have special stitch-specific Reverse actions. For other patterns, Reverse immediately makes locking stitches and stops.

• Pattern-group conditions must remain next to this answer; it is not one universal immediate-stop action.

For Utility 1, 4, 9–12; Applique 10; Quilt 1–3; and Bridge 1–6, Auto-Lock immediately makes locking stitches and stops. For other patterns it ties off at the end of the current pattern and stops. Pressed while stopped, its blinking signal arms the corresponding action for the next start. Thread Cut after Auto-Lock adds automatic trimming when enabled.

• The #30 notation is the manual’s thread designation, not an inferred diameter.
• Do not describe an unavailable cutter in these states as proof of a mechanical fault.

It does not work immediately after power-on, when the foot is raised using the presser-foot lifter, or after three consecutive presses. For thread #30 or thicker, use the manual face-plate cutter. Normally trimming raises the needle bar; its LED blinks during trimming.

• The switch is optional and its connection route is through the depicted foot control.
• Follow the full cable/base-cover setup, with power off for connection; no arbitrary pedal compatibility is implied.

The switch connects to the foot control. After sewing, wait until START/STOP is blue before depressing the cutter switch. It trims when held more than 0.5 seconds and does not work unless the foot control has first been depressed.

• Do not turn this into a universal always-down rule for all stitches or modes.

Yes. Sewing settings normally allow changing the default needle-down stop to up, but the manual explicitly says the machine stops needle-down when Foot-up is enabled even if up was selected. Buttonholes, specialty stitches and monograms have stated exceptions to the ordinary default. Pivot foot height can be adjusted for fabric thickness.

• These are separately named settings, not a guarantee that every run-out or thread fault is detected.
• The page does not establish a numeric remaining-thread threshold.

Sewing settings let the owner turn off Upper Thread Breakage Sensor to disable its needle-thread-break auto-stop, or Bobbin Thread Remaining Sensor to disable its bobbin-runs-out auto-stop.

• Foot control 21390 is optional. It is not listed here as standard equipment or a confirmed replacement purchase.
• No numerical voltage, frequency, watts, amps or universal-voltage claim is established by these pages.
• Switch off and unplug when unattended, cleaning or attaching/removing parts; do not put objects on the pedal.

The manual identifies YC-485EC-1 for its ordinary foot control and model 21390 in the optional-foot-control section. Use the supplied power cable, connect with power off, and wait five seconds after switching off before powering on again. USA/Canada polarized-plug instructions are expressly regional.

• These are Janome catalog classifications for Continental M6 / CM6. Check the actual machine and its instructions before choosing accessories.
• A shank or feed-system label does not confirm holder dimensions, adapter needs or whether a replacement foot fits.
• Catalog groups and codes do not establish alternative model names, production dates or interchangeable parts.
• This confirms the AcuFeed listing only. Follow the separate instructions for the named feet and plates: AD and HP2 are optional, and HP2 needs the optional HP plate.

Yes — AcuFeed is listed for CM6 in the cited Janome accessory catalog.

• CM6 is the catalog’s model code for Continental M6. It does not confirm shared parts with other CM models.

CM6

• Switch off and unplug first, follow the listed removal and reassembly steps, and do not dismantle beyond the manual's instructions.

Clean the hook area at least once a month.

• No drive-capacity or modern file-system support is inferred from a screenshot.
• The manual gives conflicting formatting instructions: printed page 135 describes the machine’s Format function, while printed page 145 says to use a Windows PC. A safe single formatting procedure has not been confirmed here.
• This reference does not report a tested formatting, reset or deletion procedure.

The manual supports FAT16 and FAT32 only and says not to use a USB card reader or USB hub. During a displayed memory warning, do not power off or disconnect USB because the memory bank may be damaged.

• This describes the cited mode, not every possible pattern under manual dual-feed settings.
• Use its correctly installed optional foot and drive; test fabric layers rather than assuming balance 5 fits every stack.

The ordinary dual-feed mode supports U1–U5, Q1–Q7 and some sewing applications; unsuitable patterns/controls are unavailable. Begin at balance 5 and test on the intended fabric. For a puckered lower layer increase toward 6–10; for a puckered upper layer decrease toward 1–4. The screen’s OD (twin) foot for Q2/Q3 is optional.

• Make a test stitch on the actual fabric and adjust balance if necessary.
• No universal all-pattern eligibility or bypass of greyed controls is implied.

Turning Manual Dual Feed on allows patterns beyond ordinary U1–U5/Q1–Q7, but U8, B14 and unsuitable applications stay unavailable. Its ordinary dual-feed key is greyed while manual mode is on. The setting itself is unavailable with feed dogs dropped or a feed-down application selected. Turn it off after manual dual-feed work.

• These are dimensions for that special holder application, not all permissible spool sizes or a bobbin-size specification.
• Follow the depicted holder seating and net arrangement.

The special holder is described for spool-hole diameter 9.5–10.5 mm (⅜–7⁄16 inch) and spool length 70–75 mm (2¾–3 inches). A spool net is recommended if the cone thread is shaky or kinky. Two spool pins let a bobbin be wound without unthreading the ongoing sewing setup.