Machine reference
Needles, bobbins, feet and other details for this model. Check the requirements before choosing parts.
Before choosing a part
Start with these documented details. Read the requirements with each answer before choosing a needle, bobbin or foot.
Raise the needle and presser foot; press the red button behind the holder to release the foot. Put the replacement foot pin under the holder groove and lower the holder to lock it.
Requirements and sources →Raise the presser bar and turn the thumbscrew counterclockwise to remove the holder. For attachment, loosen the thumbscrew, position the assembly on the presser bar as illustrated and tighten clockwise.
Requirements and sources →Not yet confirmed here: Manufacturer accessory group, Presser-foot shank type, Foot interface / generation, Bobbin type / class, Bobbin material, Bobbin diameter, Bobbin height, Hook type, Needle system / designation, Needle sizes by fabric and use, Maximum stitch / zigzag width, Feed system, Bobbin loading direction. What is still to confirm →
Other names, regional versions and related models have not been confirmed here. A shared manual, product line or accessory group does not identify the machine's family.
Use only this exact retained model/manual edition. Read all original safety, setup and fabric conditions with the cited answer. These instructions do not establish standardized shank or holder fit, a generic bobbin class/substitute, measured dimensions or a formal needle system.
Documents and page references →Use only this exact retained model/manual edition. Read all original safety, setup and fabric conditions with the cited answer. These instructions do not establish standardized shank or holder fit, a generic bobbin class/substitute, measured dimensions or a formal needle system.
Documents and page references →Raise the needle with the up/down button and lower the foot, then switch off and disconnect before changing the needle. Follow the complete clamp and stopper-pin instructions.
Documents and page references →Use only this exact retained model/manual edition. Read all original safety, setup and fabric conditions with the cited answer. These instructions do not establish standardized shank or holder fit, a generic bobbin class/substitute, measured dimensions or a formal needle system.
Documents and page references →Use only this exact retained model/manual edition. Read all original safety, setup and fabric conditions with the cited answer. These instructions do not establish standardized shank or holder fit, a generic bobbin class/substitute, measured dimensions or a formal needle system.
Documents and page references →Use only this exact retained model/manual edition. Read all original safety, setup and fabric conditions with the cited answer. These instructions do not establish standardized shank or holder fit, a generic bobbin class/substitute, measured dimensions or a formal needle system.
Documents and page references →Manuals, parts books & more
Publisher links below distinguish a matched file from a listing.
Choose the document for your task: an instruction manual, service manual, parts list and accessory guide answer different questions.
About this document & page references →
Instruction manualCited retained OEM instruction manual: Page references identify this edition. A matching current public download has not been established. The original is retained privately and is not hosted by SewIndex.
Read the model-specific requirements with each answer before choosing parts.
Insert the needle with its flat side to the rear, push it against the stopper pin and tighten the clamp screw firmly.
Bobbin winding stops automatically when the bobbin is fully wound.
Place the bobbin with its thread running off counterclockwise. Guide the thread into front notch A, left between the tension-spring blades and into side notch B. Pull about 10 cm (4 inches) to the rear and reattach the cover.
Raise the needle and presser foot; press the red button behind the holder to release the foot. Put the replacement foot pin under the holder groove and lower the holder to lock it.
Raise the presser bar and turn the thumbscrew counterclockwise to remove the holder. For attachment, loosen the thumbscrew, position the assembly on the presser bar as illustrated and tighten clockwise.
Use the proper foot for the selected pattern; the manual warns that the wrong foot can cause the needle to break.
Specifications apply to the named model and document edition. Read any setup, fabric or safety requirements with the answer.
No further specifications have been confirmed here. See the compatibility and operating answers above.
Use the full source procedure and its safety precautions. A short referenced answer is not a substitute for service documentation or qualified electrical/mechanical repair.
Service-manual availability and service-only procedures remain unestablished unless separately cataloged and reviewed.
Answers use the retained MC6600P instruction manual and its safety requirements. Bobbin system, needle system and general foot compatibility remain unconfirmed. The original PDFs are not hosted here.
An unanswered question does not mean a part is incompatible. We have not confirmed enough information to recommend it.
Bobbin — System: Not established Full recorded limit & conditions →
Needle — System: Not established Full recorded limit & conditions →
Presser foot — Standardized fit: Not established Full recorded limit & conditions →
Other names, regional versions, production history, further specifications and documents are not fully covered here. Their absence is not a “none exist” finding.
Each answer links to its exact evidence passage below. Open a reference to see the document and page. These links identify the source; they do not include the full manual or its diagrams. Document access is consolidated in the OEM library above.
Published by Janome · unknown_not_explicitly_established
Exact MC6600P retained manual only. Preserve procedure, regional and edition conditions; no sibling or general compatibility transfer.
Document text and page images were checked.
Document and available links →About this document →PDF page 1 · printed page cover
PDF page 14 · printed page 12
PDF page 14 · printed page 12
PDF page 19 · printed page 17
PDF page 20 · printed page 18
PDF page 25 · printed page 23
Alex Shick · Founder and editor. Corrections managed by Alex Shick.
This Janome MC6600P guide is based on documents, with AI assistance to organize the information. We have not tested or repaired the machine.
Check the document edition with each answer. A source review date is not a machine inspection date or a promise that the manual is the latest edition.
Contact the SewIndex team or report a correction ↗
The correction address has been tested and its monitoring confirmed. We cannot promise a response or accept every suggested change.
Report an error with the model, document and page · About SewIndex and our method
Answers come from the documents named on this page. They describe those editions, and may not cover later changes to the machine or manual.